Support - Smart Spot Lights

Introduction

Overview

The Atomi Smart LED Color-Changing Spot Lights are an attractive and useful addition to any home. With a tunable white light range, a spectrum of 16 million colors, and 400-lumen brightness, they’re perfect for everyday use and special occasions. Stake them in your front driveway, around your back patio, or throughout your garden.

Specifications

– 12W power adapter
– Material: Aluminum+PC
– Light Source: RGB + CW, single lamp 10W
– 400 lumens Input: 120V, 60HZ, 0.2A
– Output: 12V, max. 1A
– IP65 for outdoor use (Spot Lights)
– Connects up to 40 spot lights

Before you begin installation

1. Check if all lights have power. (See images below for details about cables and maximum distance between bridge/lights*). Then unplug the lights.
2. Make sure your mobile device is running iOS® 8 or higher or Android™ 4.1× or higher
3. Know your Wi-Fi network and password
4. Make sure you’re connected to a 2.4GHz Wi-Fi network (Atomi Smart can’t connect to 5GHz networks)
5. Confirm that your phone’s Bluetooth is enabled

Important

*IMPORTANT: The Smart Spot Lights communicate via Bluetooth Mesh Networking.
Each spot light acts as an antenna to transmit their signal between them and to the Smart Bridge.
Make sure that the closest spot light is not too far from the Smart Bridge (Maximum distance is 30-35ft). Walls and other obstacles will interfere with the signal strength. If you are experiencing connection issues, please move the Smart Bridge somewhere closer to the lights.

Connecting Your Devices

Step 1: Download App

Download the Atomi Smart app from the App Store or Google Play and create an account.
Confirm that your phone’s Bluetooth is enabled and that you are allowing the Atomi Smart app to access Bluetooth.
If you already have the app installed, please make sure to check for any updates as they will improve your experience with the Atomi Smart app.

Step 2: Plug In the Smart Bridge

1. Plug the Smart Bridge into the USB Wall Charger, and plug it into the outlet.
Tip: Place the Smart Bridge as close as possible to your lights to avoid any connection issues.
(NOTE: Only the Smart Bridge should be plugged in at this point. Keep your Spot Lights unplugged from the power outlet)
2. Confirm that the Smart Bridge indicator is flashing orange, and that the blue indicator is solid.
If the indicator is not flashing, press and hold the bridge’s button for 5 seconds. The orange indicator should start flashing after a few seconds.

Step 3: Add Smart Bridge to the app

1. Confirm that your phone’s Bluetooth is enabled.
2. Then, open the Atomi Smart app, press “Add Device” or the “+” button.
3. A popup should appear. Press “Connect device”.
If the popup did not appear, confirm that the Smart Bridge’s indicator is flashing orange. Then, close the Atomi Smart app and follow the steps above again. If it still fails to appear, select “Smart Bridge (Spot Lights)” on the device list and follow the on-screen instructions.

Step 4: Connecting to Wi-Fi

Now that the app found your Smart Bridge, the next step is to connect it to your Wi-Fi network.

1. Enter your home Wi-Fi network and password (2.4GHz only). Press ‘Continue’.

2. Your Smart Bridge is connected!

Step 5: Add Smart Spot Lights to your Smart Bridge

Now that you’ve added the Smart Bridge to the app, you can now add the Smart Spot Lights.

1. On the Atomi Smart home screen, select the Smart Bridge that you’ve just added. The screen should look like the image below.

2. Plug your Smart Spot Lights into the power outlet and confirm that the lights are flashing white. If not, press and hold each light’s power button for 10 s to reset them. (Make sure all lights are flashing).

Tip: During setup, all Spot lights should be as close as possible to the Smart Bridge. If one or more lights are not connecting it’s recommended to temporarily bring your Smart Bridge closer to them to avoid any signal issues. Once connected you can return the Smart Bridge to the original location.
Alternatively, you can connect the lights directly via Bluetooth (the same way you did for the Smart Bridge), then select ‘Add existing device’ via the Smart Bridge.

3. Select “Add new device” and follow the on-screen instructions to add the Smart Spot Lights.
4. Your Smart Spot Lights are now connected! Want to control multiple lights simultaneously? Please see below the “Creating a Group” section.
If your lights failed to connect, close the Atomi Smart app and unplug the Smart Spot Lights. Plug them back into the outlet and confirm that they are flashing white. Repeat the steps above.
Tip: If the Smart Spot Lights were already connected when you installed the Smart Bridge during “Step 2”, press “Add existing device”, and select all the available Spot Lights to be added to your Smart Bridge.

Controlling your Smart Spot Lights

Power

Power – Press ‘Power’ to turn ON/OFF your Smart Spot Lights
Timer – Add a timer to turn on/off your Smart Spot Light

White Mode

Brightness – Change your Smart Spot Lights intensity
White Wheel – Change white temperature

Color Mode

Color Wheel – Broad spectrum of colors to create the perfect ambiance.
Color Swatches – Add swatches to quickly access your favorite colors. Press and hold on a color to edit/remove your saved color
Slider 1 – Increase or decrease light brightness
Slider 2 – Change color saturation

Scenes

Select curated color scenes based on your mood.

Animated Scene Presets

Soft – Fades in and out between 2 colors

Colorful – Cycles between preset colors (Slow)

Dazzling – Cycles between preset colors (Fast)

Gorgeous – Fades between preset colors

* You can also edit any of the available scenes by pressing the ‘Edit’ button.

Scheduling

Time – Select the time to run the schedule
Repeat – Select what days of the week to repeat the schedule
Note – Adds a note/label to the schedule
Notification – Enable to receive a notification every time the schedule runs
Power – Select to turn ON or OFF the light

Hint: Create a group to schedule all of your spot lights to turn On/Off together.

More information about Creating Schedules is available here
You can also use automations to create additional schedules. Click here to learn more.

Setting automations for Sunset/Sunrise

Method 1: Scheduling via the Atomi Smart app
1. Go to the Atomi Smart app home screen and press ‘Smart Scenes’
2. Select ‘Automation’ and press the ‘+’ button
3. Press ‘Climate’ and select ‘Sunset/Sunrise’
4. Enter your City and select ‘Sunset’. Here you can add an offset to your automation (Example: turn on lights 10 minutes before sunset)
5. Press ‘Continue’
6. Press ‘Execute Device Action’ and select your smart spot light device or group (learn more about creating groups on the next section of this page or visit our Creating groups page)
7. Select ‘Power’ and choose your action (On or Off). You can also set the brightness and color temperature.
8. Press ‘Continue’. Review your Automation details and press ‘Save’.
For more Trigger & Automation instructions, visit our Trigger & Automations page

Method 2: Scheduling via the Alexa app

1. Open the Alexa app
2. Select ‘More’ and press ‘Routines’
3. Press the ‘+’ button
4. Enter a name for your routine and select ‘When this happens’
5. Press ‘Schedule’ and select Sunrise or Sunset
6. Enter your Location, Time Offset and days of the week to repeat. Press ‘Next’
7. Press ‘Add action’ and select ‘Smart Home’
8. Select your smart spot light device or group
9. Press ‘Power’ and set it to turn on or off based on your goal. Press ‘Next’ and ‘Save’

Method 3: Scheduling via the Google Home app

1. Open the Google Home app
2. Select ‘Routines’
3. Press the ‘+’ button
4. Select ‘+ Add starter’, press ‘Sunrise/sunset’ and select between Sunrise or Sunset
5. Enter your Location, Time Offset and days of the week to repeat. Press ‘Done’
6. Press ‘+ Add action’ and select ‘Adjust Home devices’
7. Click on the arrow next to ‘Adjust lights, plugs, and more’
8. Set the desired action for your devices (Example: turn on Spot Lights) and press ‘Done’
9. Confirm that the checkbox for ‘Adjust lights, plugs, and more’ is checked. Press ‘Done’
10. Now select ‘Add voice starter’, and enter any voice command. Note: You won’t need to say the voice command to trigger this routine. This is just a requirement by Google. Press ‘Save’

Creating Groups to control multiple lights together

The Atomi Smart app lets you group devices to control multiple spot lights simultaneously.

1. Make sure that all of your Smart Spot Lights are online, powered ON and connected to the Smart Bridge / app

2. Press the ‘Edit’ button (Pencil Icon) at the top right corner of one of the Smart Spot Lights’ app screen.
3. Press ‘Create Group’ and select the devices you wish to be included. Press ‘Save’. You can now control your lights simultaneously.